Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Metal Roof Installation Cost in Orlando?
Metal roof installation in Orlando, FL typically costs between $11,500 and $38,000 for a standard single-family home in 2026, with most homeowners paying around $17,000 to $24,000 for a standing seam roof on a 1,800-square-foot house. That works out to roughly $9.50 to $19.00 per square foot installed, depending on metal type, roof complexity, and whether the old roof needs to come off first. A screw-down corrugated panel roof runs lower, often $9,500 to $14,000, while premium standing seam copper or zinc systems can reach $50,000 or more on larger Orlando homes.
These numbers reflect what we see across Orange County neighborhoods, from College Park to Dr. Phillips to Winter Park. If you want a precise figure for your house, call (850) 303-7235 for a free estimate. We put the price in writing before any work starts, and that price does not change at the door.
Key takeaways:
- Most Orlando homes: $17,000 to $24,000 for standing seam metal.
- Entry-level screw-down panels: $9,500 to $14,000.
- Per-square-foot range: $9.50 to $19.00 installed.
- Orlando’s wind codes and summer heat make panel gauge and finish choices matter more than in most markets.
- Free estimates are available; call (850) 303-7235.
Metal Roof Installation Cost Breakdown (2026)
Here is the line-item breakdown we give homeowners in Orlando, taken from actual bids our team has prepared across the metro in the past 12 months.
| Cost Component | Typical Range (Orlando, 2026) | Notes |
|---|---|---|
| Metal panels (material only) | $4.50 – $11.00 per sq ft | Galvalume steel at the low end; aluminum, zinc, or copper at the top |
| Underlayment | $0.60 – $1.25 per sq ft | Synthetic underlayment recommended; peel-and-stick in valleys |
| Tear-off of existing roof | $1.00 – $3.00 per sq ft | Depends on layers; Orlando homes often have 1-2 layers of shingles |
| Labor and installation | $3.50 – $6.50 per sq ft | Standing seam is more labor-intensive than screw-down |
| Trim, flashing, and ridge cap | $800 – $2,400 total | Drip edge, eave trim, gable trim, valley flashing |
| Fasteners and clips | $500 – $1,400 total | Hidden clip systems cost more than exposed fasteners |
| Permit and inspection fees | $250 – $600 total | Orange County and city of Orlando permit costs |
| Disposal and site cleanup | $350 – $900 total | Dump fees included |
What pushes a quote toward the high end? A steep or multi-story roof, a cut-up roofline with dormers and hips, skylights or chimneys that need re-flashing, and any decking repair once the old roof comes off. What pushes it down? A simple gable roof with few penetrations, a one-story ranch, and choosing a screw-down panel system instead of standing seam.
One thing unique to Orlando: local building code requires specific wind-uplift ratings for metal roofing, particularly in areas that saw damage during Hurricane Ian and Nicole. A roof that meets Miami-Dade County standards will cost slightly more in fasteners and engineering but is worth it. We recommend upgrade-rated clips on every standing seam roof we install in Orlando, not because it pads the bid, but because we have seen what August storms do to inadequate fastening systems.
What Affects Metal Roof Installation Pricing in Orlando
- Panel profile and thickness. Screw-down corrugated or ribbed panels in 26-gauge steel run $9.50 to $13.50 per square foot installed. Standing seam with hidden fasteners in 24-gauge runs $13.00 to $19.00. Thicker steel and aluminum push material cost up by 20 to 35 percent, but they resist hail and flying debris better, which matters in Orlando’s afternoon thunderstorm season.
- Roof complexity. A simple 1,500-square-foot gable roof in Conway is straightforward. A 2,400-square-foot home in Baldwin Park with dormers, a chimney, two valleys, and a flat section over a lanai takes our crew an extra two days. Every valley, transition, and penetration means more flashing and more labor.
- Number of tear-off layers. Many Orlando homes built in the 1980s and 1990s have two layers of shingles. Removing both layers costs more in labor and dump fees than removing one. If the decking underneath is water-damaged or delaminated, replacement runs $2.50 to $4.00 per square foot extra.
- Material choice. We install products from seven manufacturers: GAF, CertainTeed, Owens Corning, IKO, Atlas, Tamko, and Boral. Within those lines, aluminum panels cost 15 to 25 percent more than steel but hold up better against Florida’s salt air if you live within a few miles of the coast. Copper and zinc are specialty orders that can double or triple the material line item.
- Season and scheduling. Orlando’s dry season from November through April is peak roofing season. Material prices are steady, but lead times stretch. Summer and early fall bring daily thunderstorms that slow installs. We do not charge a seasonal premium, but some Orlando contractors do.
- Insulation and ventilation upgrades. If your attic ventilation needs work, a metal roof is the time to fix it. Ridge vents, soffit vents, and possibly adding a radiant barrier under the metal add $1,500 to $4,000, but they cut attic temperatures significantly, which matters when Orlando hits 95 degrees in July.
Metal Roof vs. Asphalt Shingles: Cost Comparison in Orlando
An asphalt shingle roof in Orlando runs $7,500 to $14,000 for the same house where metal costs $17,000 to $24,000. So metal costs roughly two to three times as much upfront. But here is the math we walk through with every homeowner: a shingle roof in Florida lasts 15 to 20 years. A metal roof lasts 40 to 70 years. Over 50 years, you will buy two or three shingle roofs. Metal is often cheaper per year of service.
Metal also lowers cooling costs. The Florida Solar Energy Center has measured attic temperature reductions of 30 to 40 degrees with reflective metal roofing, which translates to measurable air conditioning savings in an Orlando summer. And most Florida insurers offer discounts or better terms for homes with metal roofs, especially those rated for wind uplift and impact resistance.
Standing Seam vs. Screw-Down Panels: What Orlando Homeowners Should Know
The two most common metal roof systems we install in Orlando are standing seam and exposed-fastener (screw-down) panels.
Standing seam uses interlocking panels with hidden clips. The fasteners never see weather, so the system accommodates thermal expansion and contraction, which is a real issue when a metal roof cycles from 55 degrees on a January morning to 140 degrees surface temperature in August. Standing seam runs $13.00 to $19.00 per square foot installed in Orlando. It carries the longest warranties, usually 30 to 50 years on the finish and up to lifetime on the metal itself.
Screw-down panels use exposed gasketed screws through the panel face into the purlins or decking. They run $9.50 to $13.50 per square foot installed. They are a fine choice for covered porches, carports, workshops, or homeowners on a tighter budget. The tradeoff: gaskets wear out under Florida sun and need replacement every 8 to 12 years, and the panels cannot move much with temperature swings, which can cause oil-canning or loosening over time.
For a primary residence in Orlando, we usually recommend standing seam. For a detached garage or lanai, screw-down is a sensible spend. We will show you both options with real pricing for your roof before you decide.
Orlando-Specific Considerations for Metal Roofs
Orlando throws three specific challenges at a metal roof: high wind, intense UV, and daily thermal cycling.
Wind: Orange County sits in a high-velocity hurricane zone for code purposes. Metal roofs here need fastening systems rated for uplift. A properly installed standing seam roof with upgraded clips handles 140 mph winds. A roof nailed or screwed inadequately will not. We have re-roofed homes in MetroWest and Azalea Park where previous metal installs failed at the fasteners, not the panels.
UV exposure: At Orlando’s latitude, a metal roof gets roughly 3,000 hours of sunlight per year. Paint finishes on lower-tier panels fade faster here than in northern markets. We recommend Kynar 500 or Hylar 5000 PVDF finishes from manufacturers like GAF and CertainTeed because they hold color and gloss far longer than standard polyester paints.
Thermal cycling: Orlando swings from overnight lows in the 40s to 95-plus afternoons. That is a big temperature range for a metal surface. Standing seam systems with floating clip attachments handle this expansion and contraction without stressing the fasteners. Screw-down systems do not handle it as gracefully, which is one reason we are careful about where we recommend them.
Homeowners in need of metal roof installation in Orlando should also know that a properly installed metal roof sheds rain faster than shingles, which matters during afternoon downpours that drop two inches in an hour. Valleys and eave details have to be right, or water backs up. That is a workmanship issue more than a material issue, and it is why we put our guarantee in writing on every metal roof we install.
How to Save on Metal Roof Installation
Metal roofing is a premium product, but there are legitimate ways to control the cost without cutting corners that will cost you later.
- Get the roof measured correctly. Waste factors on complex roofs run 10 to 15 percent. On a simple gable, waste should be closer to 5 percent. A sloppy estimate pads the material line. We measure twice and show you the numbers.
- Choose 26-gauge steel instead of 24-gauge. For most Orlando homes, 26-gauge standing seam is fully adequate for wind uplift and impact. You save 10 to 15 percent on material without giving up meaningful durability.
- Install over the existing roof if code allows. Florida building code permits a second roof layer in some circumstances, though we rarely recommend it. If your existing roof is a single layer, in good shape, and your decking is solid, an overlay saves the tear-off cost of $1,000 to $3,000. We will tell you honestly if it is a good idea for your house. Most of the time, tear-off is the better move.
- Do the work during our shoulder seasons. Early fall and late spring in Orlando are slower for roofing companies. We do not cut our prices seasonally, but scheduling is more flexible, and you will have more attention from the crew.
- Ask about manufacturer rebates. GAF, Owens Corning, and CertainTeed occasionally run promotions that reduce material costs. We pass those through to our customers whenever they apply.
- Skip the upgrades you do not need. Snow guards are pointless in Orlando. Copper accents are beautiful but optional. A standard ridge cap does the job without custom fabrication.
Our estimates are free and carry no obligation. Call (850) 303-7235 and we will get you a written price, not a verbal ballpark that changes later.
How the Tilehurst Roofing Process Works
When you call our Orlando office, a live person answers. Not a voicemail. Not a callback queue. We schedule a time, and our estimator arrives in the window we gave you. He walks the roof, takes measurements, checks the decking condition if accessible, and looks at the existing flashing and ventilation. Then he writes the price. You see every line item before any work is scheduled. That written price is the price. It does not change at the door.
On the day of installation, our background-checked, uniformed crew arrives on time. We protect landscaping, keep the site organized, and work until the roof is complete. At the end of the job, we walk the roof with you, confirm the details, and hand you a written guarantee. Every Tilehurst job is covered by the 365-Day Done Right Promise. If something is not right within a year, we come back and make it right at no charge. That is what operating under the Kingswell Guarantee means, and Greg Holloway holds every job to that standard.
Our material options come from seven manufacturers: GAF, CertainTeed, Owens Corning, IKO, Atlas, Tamko, and Boral. That means you get a roof that fits your home and your budget, not whatever panel happens to be in the warehouse that week.
FAQs – Metal Roof Installation Cost
Is it cheaper to repair or replace a metal roof in Orlando?
For a metal roof that is under 15 years old, targeted repairs usually run $450 to $1,800 in Orlando, which is almost always cheaper than replacement. If the roof is over 25 years old, has failed fasteners across multiple panels, or shows widespread corrosion, replacement at $11,500 to $38,000 becomes the better long-term value. We will tell you which makes sense for your roof after an inspection. Call (850) 303-7235 to schedule a look.
How much does a metal roof cost per square foot in Orlando?
Installed metal roofing in Orlando runs $9.50 to $19.00 per square foot in 2026. Screw-down panels sit at the low end, standing seam in the middle, and premium aluminum or specialty finishes at the top. That includes materials, labor, underlayment, flashing, and permit fees.
How long does metal roof installation take in Orlando?
Most single-family metal roof installations in Orlando take 3 to 7 working days. Tear-off of an existing roof adds a day. Complex cut-up rooflines add another day or two. Weather can stretch the timeline, especially during summer afternoon thunderstorms. We schedule accordingly and keep you updated daily.
Do metal roofs hold up to Orlando hurricanes and hail?
A properly installed standing seam metal roof rated for high-velocity hurricane zones handles sustained wind over 130 mph and shrugged off every storm that has hit Orange County in the past two decades. Hail resistance depends on panel gauge; 24-gauge steel resists denting better than 26-gauge. If impact resistance is a priority, ask about thicker-gauge panels from Atlas or CertainTeed.
Does a metal roof increase home value in Orlando?
Real estate appraisers in Central Florida typically credit 60 to 85 percent of the metal roof cost as added resale value. Buyers in Orlando know what a metal roof means for insurance and cooling costs, and listings with metal roofs tend to move faster in neighborhoods like Thornton Park and College Park. You likely will not recoup the full cost in a sale, but you will get most of it back, plus the savings and peace of mind while you live under it.
Can you install a metal roof over existing shingles in Orlando?
Florida code allows a metal roof over one layer of existing shingles in some cases, which saves $1,000 to $3,000 in tear-off costs. However, we recommend tear-off unless the existing roof is in excellent condition and the decking is verified sound. A metal roof is a 50-year product; installing it over a failing substrate is false economy. We will inspect and give you an honest recommendation with the numbers to back it.
Get Your Orlando Metal Roof Estimate Today
A metal roof is a significant investment, and you should know exactly what it costs before you commit. Call (850) 303-7235 and a live person will answer, day or night. We will schedule a free estimate, put a written price in your hands, and answer every question in plain language. That is how we have done it since Kingswell was founded in 2000, and it is how every Tilehurst Roofing Orlando job starts.
Written by Greg Holloway, Owner at Tilehurst Roofing Orlando. Pricing reflects the Orlando market as of 2026. Tilehurst Roofing Orlando offers free estimates – call (850) 303-7235. Return to our home page to learn more about the Kingswell Guarantee and the 365-Day Done Right Promise.
What Our Customers Say
"Had a leak over the kitchen every time it rained hard. Two other roofers wanted to replace the whole roof. Tilehurst found the bad flashing, fixed it, and it's been dry through three storms since. Honest people."
- Gary Whitfield"Small leak around the chimney flashing. They sealed it properly and it's held through a wet winter. Didn't push me toward a whole roof like the last outfit tried to."
- Bernard Oakes"The estimator climbed up, took photos, and showed me the actual problem areas instead of just talking. No pressure to replace anything that didn't need it. Repair's held up great."
- Tom Easley