Boral Gutter Replacement Nationwide

Boral Gutter Replacement: The Orlando Owner’s Guide

Boral gutter replacement in Orlando typically runs $8 to $18 per linear foot installed, which puts a standard single-story home with about 180 linear feet of gutter between $1,450 and $3,250 depending on gutter profile, downspout count, and fascia condition. We stock Boral-compatible steel and aluminum gutter sections on our trucks and can complete most residential replacements in a single day once we’re on site. Most Orlando homeowners discover they need this work after a hard afternoon thunderstorm, when they notice water pouring over the gutter lip instead of through the downspout, or when a section of gutter has pulled loose from the fascia board and is hanging at an angle.

Call (850) 303-7235

Boral is a manufacturer we know well. They’re one of seven roofing and exterior product lines we carry, alongside GAF, Owens Corning, CertainTeed, IKO, Atlas, and Tamko. Their gutter profiles are built to pair specifically with Boral roofing systems, and when a Boral gutter starts failing, it’s almost always at the seams, the end caps, or the hanger points, not in the middle of a straight run.

Which Boral Models This Applies To

Boral manufactures gutter profiles in two primary series: the standard K-style 5-inch and the larger 6-inch half-round profile used on homes with steeper roof pitches or heavier rainfall exposure. If you’re in an Orlando neighborhood like College Park or Delaney Park, you’re more likely to have the 5-inch K-style, while homes in Windermere or Bay Hill with tile or slate Boral roofing often run the 6-inch half-round to handle the extra water volume those roof systems shed.

To identify your exact Boral gutter profile, check the inside face of the gutter near a downspout for a stamped model code. Boral stamps a three-digit series number followed by the letter K or HR on most sections made after 2010. If the stamp has worn off, measure the top opening width across the gutter. Five inches means K-style, six inches or more typically means half-round. One gotcha we see regularly in Orlando: some homes built between 2005 and 2012 used Boral’s discontinued 5.5-inch profile. That size is no longer manufactured, so we fabricate matching sections from 6-inch stock and trim to fit, rather than forcing a mismatched 5-inch section into place and creating a leak point at the joint.

For the OEM versus aftermarket decision, we’re straightforward about this. Boral-branded gutter sections are still available for current models, and if your home is under an active Boral roofing warranty, we recommend staying with OEM replacements so the gutter system remains covered. For older Boral homes where the warranty has expired, quality aftermarket sections from the same gauge aluminum or galvalume steel perform identically and often cost 20 to 30 percent less. We’ll show you both prices before we start.

Signs Your Boral Gutter Replacement Is Failing

• Water overflowing the front lip during normal rain. This usually means the gutter pitch is no longer correct because a hanger has pulled loose from the fascia, or debris has backed up enough that water can’t reach the downspout. If it happens during heavy Orlando downpours but not light rain, you may simply need a larger profile, not a repair.
• Visible gaps or separation at the seam joints. Boral gutters are joined with sealant and rivets at each seam. Florida sun degrades the sealant over time, and the expansion and contraction from Orlando’s heat cycle eventually opens gaps that drip steadily even after the rain stops.
• Gutter sections sagging or pulling away from the fascia board. This is the most common failure we see on Boral homes in Orlando, especially in neighborhoods with older wood fascia like Thornton Park and the Milk District. The original hangers were spaced too far apart or the fascia wood has rotted behind them, and the weight of standing water finishes the job.
• Downspouts separating from the gutter at the drop outlet. The drop outlet is the weakest point on any gutter system, and on Boral profiles installed before 2015, the outlet was often crimped rather than riveted. Once that crimp loosens, water runs down the outside of the downspout instead of through it.
• Rust streaks or pinhole leaks on the gutter bottom. Boral steel gutters last longer than most, but Orlando’s humidity and salt air from coastal storms eventually find their way through. Pinhole leaks are repairable short-term, but if you can see daylight through the metal, the section is done.

Replacement Cost & What’s Included

For Orlando homes, here’s the price picture we give before we ever touch a ladder:

• 5-inch K-style aluminum replacement: $8 to $12 per linear foot installed
• 6-inch half-round replacement: $12 to $18 per linear foot installed
• Downspout replacement (each): $75 to $150 depending on height and number of elbows
• Fascia board repair or replacement (per 8-foot section): $60 to $120 if we find rot behind the old gutter

Every quote includes removal and haul-away of the old sections, new hangers spaced correctly for Florida wind load, sealant at every seam and end cap, and a full day’s labor. We write the price down before we start, and it doesn’t change at the door. If we open up the fascia and find rot that wasn’t visible from the outside, we stop and show you a separate line-item price before touching that wood. The gutter work itself carries our workmanship warranty through the 365-Day Done Right Promise, and the Boral or aftermarket materials carry their manufacturer warranty.

DIY or Call Us?

Gutter replacement sits in a strange middle ground. It looks simple from the ground, and a homeowner with a stable extension ladder, a second pair of hands, and experience with a rivet gun can absolutely swap a straight section. But most of the Boral gutter failures we repair in Orlando happen because the original install was done poorly, not because the material failed. Matching a discontinued profile, re-pitching a 30-foot run so water actually slopes to the downspout, and getting the hangers anchored into solid wood rather than rotted fascia are the things that separate a gutter that lasts fifteen years from one that pulls loose again in two.

There’s also a safety reality here. Working off a ladder at gutter height while handling a 10-foot metal section on a windy afternoon is genuinely dangerous, and we’d rather you not do it. If you’re unsure whether the problem is the gutter, the fascia behind it, or the roof edge flashing, call us at (850) 303-7235. We’ll walk the roof with you, show you exactly what’s failing, and give you a written number before any work starts. We tell you the price before we touch the roof, and we mean it.

FAQs